×
文章来源 : 广东三亿体育在线检测 发表时间：2021-11-29 浏览数量：
AEC-Q200是车规无源器件应力测试标准，AEC-Q200认证是被动元件汽车级品质认证，被动元器件厂家要进入汽车领域，必须要通过AECQ200测试。广东三亿体育在线检测是专业第三方AEC-Q200认证测试机构，接下来为大家介绍AECQ200测试项目。
AEC-Q200 REV D标准TABLE 1定义了AECQ200的所有测试项目及样品数量要求，TABLE 2 - TABLE 14分别针对不同的产品定义了测试项目及测试要求。
| TABLE 1 - QUALIFICATION SAMPLE SIZE REQUIREMENTS 表1-认证测试样品数量要求 | |||||
| Stress 应力方式 | NO. | Note 注释 | Sample Size Per Lot 样品数/批 | Number of lots 批次 | Accept on Number failed 接受标准 |
| Pre-and Post-Stress Electrical Test 应力测试前后电气测试 | 1 | G | All qualification parts submitted for testing | 0 | |
| High Temperature Exposure 高温存储 | 3 | DG | 77 Note B | 1 | 0 |
| Temperature Cycling 温度循环 | 4 | DG | 77 Note B | 1 | 0 |
| Destructive Physical Analysis 破坏性物理分析 | 5 | DG | 10 Note B | 1 | 0 |
| Moisture Resistance 湿度抵抗 | 6 | DG | 77 Note B | 1 | 0 |
| Humidity Bias 偏高湿度 | 7 | DG | 77 Note B | 1 | 0 |
| High Temperature Operating Life 高温工作寿命 | 8 | DG | 77 Note B | 1 | 0 |
| External Visual 外观 | 9 | NG | All qualification parts submitted 所有提交认证的产品 | 0 | |
| Physical Dimensions 尺寸 | 10 | NG | 30 | 1 | 0 |
| Terminal Strength 端子强度 | 11 | DGL | 30 | 1 | 0 |
| Resistance to Solvent 溶剂抵抗 | 12 | DG | 5 | 1 | 0 |
| Mechanical Shock 机械冲击 | 13 | DG | 30 Note B | 1 | 0 |
| Vibration 振动 | 14 | DG | |||
| Resistance to Solder Heat 抗焊接热 | 15 | DG | 30 | 1 | 0 |
| Thermal Shock 热冲击 | 16 | DG | 30 | 1 | 0 |
| ESD 静电放电 | 17 | D | 15 | 1 | 0 |
| Solderability 可焊性 | 18 | D | 15 each condition 每种条件 | 1 | 0 |
| Electrical Characterization 电气特性 | 19 | NG | 30 Note A 注意事项A | 3 | 0 |
| Flammability 可燃性 | 20 | D | Present certificate of compliance 提供合格证明书 | ||
| Board Flex 板弯曲 | 21 | DS | 30 | 1 | 0 |
| Terminal Strength (SMD) 端子强度（表面贴装元件） | 22 | DS | 30 | 1 | 0 |
| Beam Load 射束负载（断裂强度） | 23 | DG | 30 | 1 | 0 |
| Flame Retardance 阻燃测试 | 24 | DG | 30 | 1 | 0 |
| Rotation Life 旋转寿命 | 25 | DG | 30 | 1 | 0 |
| Surge Voltage 浪涌电压 | 27 | DG | 30 | 1 | 0 |
| Salt Spray 盐雾测试 | 29 | DG | 30 | 1 | 0 |
| Electrical Transient Conduction 瞬时电传导 | 30 | DG | 30 | 1 | 0 |
| Shear Strength 剪切强度 | 31 | DG | 30 | 1 | 0 |
| Short Circuit Fault Current Durability 短路失效电流持久性 | 32 | DG | 30 | 1 | 0 |
| Fault Current Durability 失效电流持久性 | 33 | DG | 30 | 1 | 0 |
| End-of-Life Mode Verification 寿命终止模式验证 | 34 | DG | 30 | 1 | 0 |
| Jump Start Endurance 助推启动持久性 | 35 | DG | 30 | 1 | 0 |
| Load Dump Endurance 突缷负荷持久性 | 36 | DG | 30 | 1 | 0 |
LEGEND FOR TABLE 1 表1说明
Note:
A For parametric verification data, sometimes circumstances may neccessitate the acceptance of only one lot by the user. Should a subsequent user decide to use a previous user's qualification approval, it will be the subsequent user's responsibility to verify an acceptable number of lots were used.
对于参数验证数据，有时情况可能需要用户仅接受一个批次。如果后续用户决定使用先前用户的资格认证，则后续用户将负责验证使用的批次数量是否可接受。
B Where generic (family) data is provided in lieu of component specific data, 3 lots are required.
如果提供通用（系列）数据代替部件特定数据，则需要3批。
H Required for hermetic packaged devices only.
仅适用于密封包装设备。
L Required for leaded devices only.
仅限含铅设备。
N Nondestructive test, devices can be used to populate other tests or they can be used for production.
无损检测，设备可用于填充其他测试或用于生产。
D Destructive test, devices are not to be reused for qualification or production.
破坏性试验，设备不得重复用于鉴定或生产。
S Required for surface mount devices only.
仅适用于表面安装设备。
G Generic data allowed. See Section 2.3.
允许通用数据。见第2.3节。
获取报价
如果您对我司的产品或服务有任何意见或者建议，您可以通过这个渠道给予三亿体育在线反馈。您的留言三亿体育在线会尽快回复！
0769-82327388
微信订阅号
微信咨询
